dellos9_command – Run commands on remote devices running Dell OS9

From Get docs
Ansible/docs/2.7/modules/dellos9 command module


dellos9_command – Run commands on remote devices running Dell OS9

New in version 2.2.


Synopsis

  • Sends arbitrary commands to a Dell OS9 node and returns the results read from the device. This module includes an argument that will cause the module to wait for a specific condition before returning or timing out if the condition is not met.
  • This module does not support running commands in configuration mode. Please use dellos9_config to configure Dell OS9 devices.

Parameters

Parameter Choices/Defaults Comments

commands

- / required

List of commands to send to the remote dellos9 device over the configured provider. The resulting output from the command is returned. If the wait_for argument is provided, the module is not returned until the condition is satisfied or the number of retries has expired.

interval

-

Default:

1

Configures the interval in seconds to wait between retries of the command. If the command does not pass the specified conditions, the interval indicates how long to wait before trying the command again.

match

-

added in 2.5

  • any
  • all

The match argument is used in conjunction with the wait_for argument to specify the match policy. Valid values are all or any. If the value is set to all then all conditionals in the wait_for must be satisfied. If the value is set to any then only one of the values must be satisfied.

provider

-

A dict object containing connection details.

host

- / required

Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.

password

-

Password to authenticate the SSH session to the remote device. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_PASSWORD will be used instead.

port

-

Default:

22

Specifies the port to use when building the connection to the remote device.

ssh_keyfile

-

Path to an ssh key used to authenticate the SSH session to the remote device. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_SSH_KEYFILE will be used instead.

timeout

-

Default:

10

Specifies idle timeout (in seconds) for the connection. Useful if the console freezes before continuing. For example when saving configurations.

username

-

User to authenticate the SSH session to the remote device. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_USERNAME will be used instead.

retries

-

Default:

10

Specifies the number of retries a command should be tried before it is considered failed. The command is run on the target device every retry and evaluated against the wait_for conditions.

wait_for

-

added in 2.2

List of conditions to evaluate against the output of the command. The task will wait for each condition to be true before moving forward. If the conditional is not true within the configured number of retries, the task fails. See examples.



Notes

Note

  • This module requires Dell OS9 version 9.10.0.1P13 or above.
  • This module requires to increase the ssh connection rate limit. Use the following command ip ssh connection-rate-limit 60 to configure the same. This can be done via dellos9_config module as well.
  • For more information on using Ansible to manage Dell EMC Network devices see https://www.ansible.com/ansible-dell-networking.


Examples

tasks:
  - name: run show version on remote devices
    dellos9_command:
      commands: show version

  - name: run show version and check to see if output contains OS9
    dellos9_command:
      commands: show version
      wait_for: result[0] contains OS9

  - name: run multiple commands on remote nodes
    dellos9_command:
      commands:
        - show version
        - show interfaces

  - name: run multiple commands and evaluate the output
    dellos9_command:
      commands:
        - show version
        - show interfaces
      wait_for:
        - result[0] contains OS9
        - result[1] contains Loopback

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description

failed_conditions

list

failed

The list of conditionals that have failed


Sample:

['...', '...']

stdout

list

always apart from low level errors (such as action plugin)

The set of responses from the commands


Sample:

['...', '...']

stdout_lines

list

always apart from low level errors (such as action plugin)

The value of stdout split into a list


Sample:

[['...', '...'], ['...'], ['...']]

warnings

list

always

The list of warnings (if any) generated by module based on arguments


Sample:

['...', '...']




Status

Authors

  • Dhivya P (@dhivyap)

Hint

If you notice any issues in this documentation you can edit this document to improve it.


© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.7/modules/dellos9_command_module.html