community.network.cnos_interface – Manage Interface on Lenovo CNOS network devices

Note

This plugin is part of the community.network collection (version 1.3.0).

To install it use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.cnos_interface.

Synopsis
Parameters
Notes
Examples
Return Values

Synopsis

This module provides declarative management of Interfaces on Lenovo CNOS network devices.

Parameters

Parameter		Choices/Defaults	Comments
aggregate string			List of Interfaces definitions.
delay string		Default: 20	Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values `up`/`down`, tx_rate and rx_rate
description string			Description of Interface.
duplex string		full half auto ←	Interface link status
enabled boolean		no yes ←	Interface link status.
mtu string			Maximum size of transmit packet.
name string / required			Name of the Interface.
neighbors string			Check operational state of given interface `name` for LLDP neighbor. The following suboptions are available.
	host string		LLDP neighbor host for given interface `name`.
	port string		LLDP neighbor port to which interface `name` is connected.
provider string			Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli`. For more information please see the CNOS Platform Options guide. A dict object containing connection details.
	auth_pass string		Specifies the password to use if required to enter privileged mode on the remote device. If authorize is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTH_PASS` will be used instead.
	authorize boolean	no ← yes	Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTHORIZE` will be used instead.
	host string / required		Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
	password string		Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_PASSWORD` will be used instead.
	port string	Default: 22	Specifies the port to use when building the connection to the remote device.
	ssh_keyfile string		Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_SSH_KEYFILE` will be used instead.
	timeout string	Default: 10	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
	username string		Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_USERNAME` will be used instead.
rx_rate string			Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
speed string			Interface link speed.
state string		present ← absent up down	State of the Interface configuration, `up` means present and operationally up and `down` means present and operationally `down`
tx_rate string			Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules

Notes

Note

Tested against CNOS 10.8.1

Examples

- name: Configure interface
  community.network.cnos_interface:
      name: Ethernet1/33
      description: test-interface
      speed: 100
      duplex: half
      mtu: 999

- name: Remove interface
  community.network.cnos_interface:
    name: loopback3
    state: absent

- name: Make interface up
  community.network.cnos_interface:
    name: Ethernet1/33
    enabled: True

- name: Make interface down
  community.network.cnos_interface:
    name: Ethernet1/33
    enabled: False

- name: Check intent arguments
  community.network.cnos_interface:
    name: Ethernet1/33
    state: up
    tx_rate: ge(0)
    rx_rate: le(0)

- name: Check neighbors intent arguments
  community.network.cnos_interface:
    name: Ethernet1/33
    neighbors:
    - port: eth0
      host: netdev

- name: Config + intent
  community.network.cnos_interface:
    name: Ethernet1/33
    enabled: False
    state: down

- name: Add interface using aggregate
  community.network.cnos_interface:
    aggregate:
    - { name: Ethernet1/33, mtu: 256, description: test-interface-1 }
    - { name: Ethernet1/44, mtu: 516, description: test-interface-2 }
    duplex: full
    speed: 100
    state: present

- name: Delete interface using aggregate
  community.network.cnos_interface:
    aggregate:
    - name: loopback3
    - name: loopback6
    state: absent

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
commands list / elements=string	always, except for the platforms that use Netconf transport to manage the device.	The list of configuration mode commands to send to the device. Sample: ['interface Ethernet1/33', 'description test-interface', 'duplex half', 'mtu 512']

Authors

Anil Kumar Muraleedharan(@amuraleedhar)

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.10/collections/community/network/cnos_interface_module.html