cisco.iosxr.iosxr_interface – (deprecated, removed after 2022-06-01) Manage Interface on Cisco IOS XR network devices

cisco.iosxr.iosxr_interface – (deprecated, removed after 2022-06-01) Manage Interface on Cisco IOS XR network devices

Note

This plugin is part of the cisco.iosxr collection (version 1.2.0).

To install it use: ansible-galaxy collection install cisco.iosxr.

To use it in a playbook, specify: cisco.iosxr.iosxr_interface.

New in version 1.0.0: of cisco.iosxr

• DEPRECATED
• Synopsis
• Requirements
• Parameters
• Notes
• Examples
• Return Values
• Status

DEPRECATED

Removed in

major release after 2022-06-01

Why

Newer and updated modules released with more functionality in Ansible 2.9

Alternative

iosxr_interfaces

Synopsis

• This module provides declarative management of Interfaces on Cisco IOS XR network devices.

Note

This module has a corresponding action plugin.

Requirements

The below requirements are needed on the host that executes this module.

• ncclient >= 0.5.3 when using netconf
• lxml >= 4.1.1 when using netconf

Parameters

Parameter		Choices/Defaults	Comments
active string		active ← preconfigure	Whether the interface is active or preconfigured. Preconfiguration allows you to configure modular services cards before they are inserted into the router. When the cards are inserted, they are instantly configured. Active cards are the ones already inserted.
aggregate list / elements=dictionary			List of interfaces definition
	active string	active preconfigure	Whether the interface is active or preconfigured. Preconfiguration allows you to configure modular services cards before they are inserted into the router. When the cards are inserted, they are instantly configured. Active cards are the ones already inserted.
	delay integer		Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values up/down, tx_rate and rx_rate.
	description string		Description of Interface being configured.
	duplex string	full half	Configures the interface duplex mode. Default is auto-negotiation when not configured.
	enabled boolean	no yes	Removes the shutdown configuration, which removes the forced administrative down on the interface, enabling it to move to an up or down state.
	mtu string		Sets the MTU value for the interface. Range is between 64 and 65535'
	name string		Name of the interface to configure in type + path format. e.g. GigabitEthernet0/0/0/0
	rx_rate string		Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
	speed string	10 100 1000	Configure the speed for an interface. Default is auto-negotiation when not configured.
	state string	present absent up down	State of the Interface configuration, up means present and operationally up and down means present and operationally down
	tx_rate string		Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
delay integer		Default: 10	Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values up/down, tx_rate and rx_rate.
description string			Description of Interface being configured.
duplex string		full half	Configures the interface duplex mode. Default is auto-negotiation when not configured.
enabled boolean		no yes ←	Removes the shutdown configuration, which removes the forced administrative down on the interface, enabling it to move to an up or down state.
mtu string			Sets the MTU value for the interface. Range is between 64 and 65535'
name string / required			Name of the interface to configure in type + path format. e.g. GigabitEthernet0/0/0/0
provider dictionary			Deprecated Starting with Ansible 2.5 we recommend using connection: network_cli. For more information please see the Network Guide. A dict object containing connection details.
	host string		Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
	password string		Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_PASSWORD will be used instead.
	port integer		Specifies the port to use when building the connection to the remote device.
	ssh_keyfile path		Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_SSH_KEYFILE will be used instead.
	timeout integer		Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
	transport string	cli ← netconf	Specifies the type of connection based transport.
	username string		Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_USERNAME will be used instead.
rx_rate string			Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
speed string		10 100 1000	Configure the speed for an interface. Default is auto-negotiation when not configured.
state string		present ← absent up down	State of the Interface configuration, up means present and operationally up and down means present and operationally down
tx_rate string			Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules

Notes

Note

• This module works with connection network_cli and netconf. See the IOS-XR Platform Options.
• Tested against IOS XRv 6.1.3.
• Preconfiguration of physical interfaces is not supported with netconf transport.
• For more information on using Ansible to manage network devices see the Ansible Network Guide
• For more information on using Ansible to manage Cisco devices see the Cisco integration page.

Examples

- name: configure interface
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/2
    description: test-interface
    speed: 100
    duplex: half
    mtu: 512

- name: remove interface
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/2
    state: absent

- name: make interface up
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/2
    enabled: true

- name: make interface down
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/2
    enabled: false

- name: Create interface using aggregate
  cisco.iosxr.iosxr_interface:
    aggregate:
    - name: GigabitEthernet0/0/0/3
    - name: GigabitEthernet0/0/0/2
    speed: 100
    duplex: full
    mtu: 512
    state: present

- name: Create interface using aggregate along with additional params in aggregate
  cisco.iosxr.iosxr_interface:
    aggregate:
    - {name: GigabitEthernet0/0/0/3, description: test-interface 3}
    - {name: GigabitEthernet0/0/0/2, description: test-interface 2}
    speed: 100
    duplex: full
    mtu: 512
    state: present

- name: Delete interface using aggregate
  cisco.iosxr.iosxr_interface:
    aggregate:
    - name: GigabitEthernet0/0/0/3
    - name: GigabitEthernet0/0/0/2
    state: absent

- name: Check intent arguments
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/5
    state: up
    delay: 20

- name: Config + intent
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/5
    enabled: false
    state: down
    delay: 20

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
commands list / elements=string	always (empty list when no commands to send)	The list of configuration mode commands sent to device with transport cli Sample: ['interface GigabitEthernet0/0/0/2', 'description test-interface', 'duplex half', 'mtu 512']
xml list / elements=string	always (empty list when no xml rpc to send)	NetConf rpc xml sent to device with transport netconf Sample: [' act GigabitEthernet0/0/0/0 test-interface-0 GigabitEthernet 512 100 half ']

Status

• This module will be removed in a major release after 2022-06-01. [deprecated]
• For more information see DEPRECATED.

Authors

• Ganesh Nalawade (@ganeshrn)
• Kedar Kekan (@kedarX)

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.10/collections/cisco/iosxr/iosxr_interface_module.html