icx_interface – Manage Interface on Ruckus ICX 7000 series switches

icx_interface – Manage Interface on Ruckus ICX 7000 series switches

New in version 2.9.

• Synopsis
• Parameters
• Notes
• Examples
• Return Values
• Status

Synopsis

• This module provides declarative management of Interfaces on ruckus icx devices.

Parameters

Parameter			Choices/Defaults	Comments
aggregate list				List of Interfaces definitions.
	check_running_config boolean		no yes	Check running configuration. This can be set as environment variable. Module will use environment variable value(default:True), unless it is overridden, by specifying it as module parameter.
	delay integer			Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values up/down, tx_rate and rx_rate.
	description string			Name of the description.
	enabled boolean		no yes	Interface link status
	name string			Name of the Interface.
	neighbors list			Check the operational state of given interface name for CDP/LLDP neighbor. The following suboptions are available.
		host string		CDP/LLDP neighbor host for given interface name.
		port string		CDP/LLDP neighbor port to which given interface name is connected.
	power dictionary			Inline power on Power over Ethernet (PoE) ports.
		by_class string	0 1 2 3 4	The range is 0-4 The power limit based on class value for given interface name
		enabled boolean	no yes	enable/disable the poe of the given interface name
		limit string		The range is 1000-15400|30000mW. For PoH ports the range is 1000-95000mW The power limit based on actual power value for given interface name
		priority string	1 2 3	The range is 1 (highest) to 3 (lowest) The priority for power management or given interface name
	rx_rate string			Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
	speed string		10-full 10-half 100-full 100-half 1000-full 1000-full-master 1000-full-slave 10g-full 10g-full-master 10g-full-slave 2500-full 2500-full-master 2500-full-slave 5g-full 5g-full-master 5g-full-slave auto	Interface link speed/duplex
	state string		present absent up down	State of the Interface configuration, up means present and operationally up and down means present and operationally down
	stp boolean		no yes	enable/disable stp for the interface
	tx_rate string			Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
check_running_config boolean			no yes ←	Check running configuration. This can be set as environment variable. Module will use environment variable value(default:True), unless it is overridden, by specifying it as module parameter.
delay integer			Default: 10	Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values up/down, tx_rate and rx_rate.
description string				Name of the description.
enabled boolean			no yes ←	Interface link status
name string				Name of the Interface.
neighbors list				Check the operational state of given interface name for CDP/LLDP neighbor. The following suboptions are available.
	host string			CDP/LLDP neighbor host for given interface name.
	port string			CDP/LLDP neighbor port to which given interface name is connected.
power dictionary				Inline power on Power over Ethernet (PoE) ports.
	by_class string		0 1 2 3 4	The range is 0-4 The power limit based on class value for given interface name
	enabled boolean		no ← yes	enable/disable the poe of the given interface name
	limit string			The range is 1000-15400|30000mW. For PoH ports the range is 1000-95000mW The power limit based on actual power value for given interface name
	priority string		1 2 3	The range is 1 (highest) to 3 (lowest) The priority for power management or given interface name
rx_rate string				Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
speed string			10-full 10-half 100-full 100-half 1000-full 1000-full-master 1000-full-slave 10g-full 10g-full-master 10g-full-slave 2500-full 2500-full-master 2500-full-slave 5g-full 5g-full-master 5g-full-slave auto	Interface link speed/duplex
state string			present ← absent up down	State of the Interface configuration, up means present and operationally up and down means present and operationally down
stp boolean			no yes	enable/disable stp for the interface
tx_rate string				Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules

Notes

Note

• Tested against ICX 10.1.
• For information on using ICX platform, see the ICX OS Platform Options guide.

Examples

- name: enable ethernet port and set name
  icx_interface:
    name: ethernet 1/1/1
    description: interface-1
    stp: true
    enabled: true

- name: disable ethernet port 1/1/1
  icx_interface:
      name: ethernet 1/1/1
      enabled: false

- name: enable ethernet port range, set name and speed.
  icx_interface:
      name: ethernet 1/1/1 to 1/1/10
      description: interface-1
      speed: 100-full
      enabled: true

- name: enable poe. Set class.
  icx_interface:
      name: ethernet 1/1/1
      power:
       by_class: 2

- name: configure poe limit of interface
  icx_interface:
      name: ethernet 1/1/1
      power:
       limit: 10000

- name: disable poe of interface
  icx_interface:
      name: ethernet 1/1/1
      power:
       enabled: false

- name: set lag name for a range of lags
  icx_interface:
      name: lag 1 to 10
      description: test lags

- name: Disable lag
  icx_interface:
      name: lag 1
      enabled: false

- name: enable management interface
  icx_interface:
      name: management 1
      enabled: true

- name: enable loopback interface
  icx_interface:
      name: loopback 10
      enabled: true

- name: Add interface using aggregate
  icx_interface:
      aggregate:
      - { name: ethernet 1/1/1, description: test-interface-1, power: { by_class: 2 } }
      - { name: ethernet 1/1/3, description: test-interface-3}
      speed: 10-full
      enabled: true

- name: Check tx_rate, rx_rate intent arguments
  icx_interface:
    name: ethernet 1/1/10
    state: up
    tx_rate: ge(0)
    rx_rate: le(0)

- name: Check neighbors intent arguments
  icx_interface:
    name: ethernet 1/1/10
    neighbors:
    - port: 1/1/5
      host: netdev

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
commands list	always	The list of configuration mode commands to send to the device. Sample: ['interface ethernet 1/1/1', 'port-name interface-1', 'state present', 'speed-duplex 100-full', 'inline power priority 1']

Status

• This module is not guaranteed to have a backwards compatible interface. [preview]
• This module is maintained by the Ansible Community. [community]

Authors

• Ruckus Wireless (@Commscope)

Hint

If you notice any issues in this documentation, you can edit this document to improve it.

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.9/modules/icx_interface_module.html