na_elementsw_network_interfaces – NetApp Element Software Configure Node Network Interfaces

From Get docs
Ansible/docs/2.8/modules/na elementsw network interfaces module


na_elementsw_network_interfaces – NetApp Element Software Configure Node Network Interfaces

New in version 2.7.


Synopsis

  • Configure Element SW Node Network Interfaces for Bond 1G and 10G IP address.

Requirements

The below requirements are needed on the host that executes this module.

  • The modules were developed with SolidFire 10.1
  • solidfire-sdk-python (1.1.0.92) or greater. Install using ‘pip install solidfire-sdk-python’

Parameters

Parameter Choices/Defaults Comments

bond_mode_10g

-

  • ActivePassive

  • ALB
  • LACP

Bond mode for 10GbE configuration.

bond_mode_1g

-

  • ActivePassive

  • ALB
  • LACP

Bond mode for 1GbE configuration.

dns_nameservers

-

List of addresses for domain name servers.

dns_search_domains

-

List of DNS search domains.

gateway_address_10g

- / required

Router network address to send packets out of the local network.

gateway_address_1g

- / required

Router network address to send packets out of the local network.

hostname

- / required

The hostname or IP address of the SolidFire cluster.

ip_address_10g

- / required

IP address for the 10G network.

ip_address_1g

- / required

IP address for the 1G network.

lacp_10g

-

  • Fast
  • Slow

Link Aggregation Control Protocol useful only if LACP is selected as the Bond Mode.

Slow - Packets are transmitted at 30 second intervals.

Fast - Packets are transmitted in 1 second intervals.

lacp_1g

-

  • Fast
  • Slow

Link Aggregation Control Protocol useful only if LACP is selected as the Bond Mode.

Slow - Packets are transmitted at 30 second intervals.

Fast - Packets are transmitted in 1 second intervals.

method

- / required

  • loopback
  • manual
  • dhcp
  • static

Type of Method used to configure the interface.

method depends on other settings such as the use of a static IP address, which will change the method to static.

loopback - Used to define the IPv4 loopback interface.

manual - Used to define interfaces for which no configuration is done by default.

dhcp - May be used to obtain an IP address via DHCP.

static - Used to define Ethernet interfaces with statically allocated IPv4 addresses.

mtu_10g

-

Default:

"1500"

Maximum Transmission Unit for 10GbE, Largest packet size that a network protocol can transmit.

Must be greater than or equal to 1500 bytes.

mtu_1g

-

Default:

"1500"

Maximum Transmission Unit for 1GbE, Largest packet size that a network protocol can transmit.

Must be greater than or equal to 1500 bytes.

password

- / required

Password for the specified user.


aliases: pass

subnet_10g

- / required

10GbE Subnet Mask.

subnet_1g

- / required

1GbE Subnet Mask.

username

- / required

Please ensure that the user has the adequate permissions. For more information, please read the official documentation https://mysupport.netapp.com/documentation/docweb/index.html?productID=62636&language=en-US.


aliases: user

virtual_network_tag

-

This is the primary network tag. All nodes in a cluster have the same VLAN tag.



Notes

Note

  • The modules prefixed with na\_elementsw are built to support the SolidFire storage platform.


Examples

- name: Set Node network interfaces configuration for Bond 1G and 10G properties
  tags:
  - elementsw_network_interfaces
  na_elementsw_network_interfaces:
    hostname: "{{ elementsw_hostname }}"
    username: "{{ elementsw_username }}"
    password: "{{ elementsw_password }}"
    method: static
    ip_address_1g: 10.226.109.68
    ip_address_10g: 10.226.201.72
    subnet_1g: 255.255.255.0
    subnet_10g: 255.255.255.0
    gateway_address_1g: 10.193.139.1
    gateway_address_10g: 10.193.140.1
    mtu_1g: 1500
    mtu_10g: 9000
    bond_mode_1g: ActivePassive
    bond_mode_10g: LACP
    lacp_10g: Fast

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description

msg

string

success

Success message





Status

Authors

Hint

If you notice any issues in this documentation you can edit this document to improve it.


© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.8/modules/na_elementsw_network_interfaces_module.html