gzip reduces the size of the named files using Lempel–Ziv coding
(LZ77). Whenever possible, each file is replaced by one with the
.gz’, while keeping the same ownership modes, access and
modification times. (The default extension is
z’ for MSDOS, OS/2 FAT and Atari.)
If no files are specified or
if a file name is
-, the standard input is compressed to the standard
gzip will only attempt to compress regular files. In
particular, it will ignore symbolic links.
If the new file name is too long for its file system,
gzip attempts to truncate only the parts of the
file name longer than 3 characters. (A part is delimited by dots.) If
the name consists of small parts only, the longest parts are truncated.
For example, if file names are limited to 14 characters, gzip.msdos.exe
is compressed to gzi.msd.exe.gz. Names are not truncated on systems
which do not have a limit on file name length.
gzip keeps the original file name in the
compressed file. This can be useful when decompressing the file with
-N if the compressed file name was truncated after a file
If the original is a regular file,
gzip by default keeps its
timestamp in the compressed file. This can be useful when
decompressing the file with
-N if the timestamp was not
preserved after a file transfer.
However, due to limitations in the current
format, fractional seconds are discarded. Also, timestamps must fall
within the range 1970-01-01 00:00:01 through 2106-02-07 06:28:15
UTC, and hosts whose operating systems use 32-bit timestamps
are further restricted to timestamps no later than 2038-01-19
03:14:07 UTC. The upper bounds assume the typical case
where leap seconds are ignored.
Compressed files can be restored to their original form using ‘
zcat. If the original name saved in the
compressed file is not suitable for its file system, a new name is
constructed from the original one to make it legal.
gunzip takes a list of files on its command line and replaces
each file whose name ends with ‘
-z’, or ‘
_z’ (ignoring case)
and which begins with the correct
magic number with an uncompressed file without the original extension.
gunzip also recognizes the special extensions ‘
.taz’ as shorthands for ‘
.tar.gz’ and ‘
respectively. When compressing,
gzip uses the ‘
extension if necessary instead of truncating a file with a ‘
gunzip can currently decompress files created by
pack. The detection of the input
format is automatic. When using the first two formats,
checks a 32 bit CRC (cyclic redundancy check). For
gunzip checks the uncompressed length. The
was not designed to allow consistency checks. However
sometimes able to detect a bad ‘
.Z’ file. If you get an error when
uncompressing a ‘
.Z’ file, do not assume that the ‘
.Z’ file is
correct simply because the standard
uncompress does not complain.
This generally means that the standard
uncompress does not check
its input, and happily generates garbage output. The SCO ‘
compress -H’ format (LZH compression method) does not include a CRC but
also allows some consistency checks.
Files created by
zip can be uncompressed by
gzip only if
they have a single member compressed with the “deflation” method. This
feature is only intended to help conversion of
tar.zip files to
tar.gz format. To extract a
zip file with a single
member, use a command like ‘
gunzip <foo.zip’ or ‘
gunzip -S .zip foo.zip’. To extract
zip files with several
unzip instead of
zcat is identical to ‘
uncompresses either a list of files on the command line or its standard
input and writes the uncompressed data on standard output.
will uncompress files that have the correct magic number whether they
have a ‘
.gz’ suffix or not.
gzip uses the Lempel–Ziv algorithm used in
The amount of compression obtained depends on the size of the input and
the distribution of common substrings. Typically, text such as source
code or English is reduced by 60–70%. Compression is generally much
better than that achieved by LZW (as used in
coding (as used in
pack), or adaptive Huffman coding
Compression is always performed, even if the compressed file is slightly
larger than the original. The worst case expansion is a few bytes for
gzip file header, plus 5 bytes every 32K block, or an expansion
ratio of 0.015% for large files. Note that the actual number of used
disk blocks almost never increases.
gzip normally preserves the mode,
ownership and timestamps of files when compressing or decompressing.
gzip file format is specified in P. Deutsch, GZIP file
format specification version 4.3,
Internet RFC 1952 (May
zip deflation format is specified in P. Deutsch,
DEFLATE Compressed Data Format Specification version 1.3,
Internet RFC 1951 (May