tee: Redirect output to multiple files or processes
tee command copies standard input to standard output and also
to any files given as arguments. This is useful when you want not only
to send some data down a pipe, but also to save a copy. Synopsis:
tee [option]… [file]…
If a file being written to does not already exist, it is created. If a
file being written to already exists, the data it previously contained
is overwritten unless the
-a option is used.
In previous versions of GNU coreutils (v5.3.0 - v8.23), a
file of ‘
tee to send another copy of input to standard output.
However, as the interleaved output was not very useful,
conforms to POSIX which explicitly mandates it to treat ‘
-’ as a file
with such name.
The program accepts the following options. Also see Common options.
Append standard input to the given files rather than overwriting them.
Ignore interrupt signals.
Adjust the behavior with errors on the outputs, with the long form option supporting selection between the following
Warn on error opening or writing any output, including pipes. Writing is continued to still open files/pipes. Exit status indicates failure if any output has an error.
This is the default
modewhen not specified, or when the short form
-pis used. Warn on error opening or writing any output, except pipes. Writing is continued to still open files/pipes. Exit status indicates failure if any non pipe output had an error.
Exit on error opening or writing any output, including pipes.
Exit on error opening or writing any output, except pipes.
tee command is useful when you happen to be transferring a large
amount of data and also want to summarize that data without reading
it a second time. For example, when you are downloading a DVD image,
you often want to verify its signature or checksum right away.
The inefficient way to do it is simply:
wget https://example.com/some.iso && sha1sum some.iso
One problem with the above is that it makes you wait for the download to complete before starting the time-consuming SHA1 computation. Perhaps even more importantly, the above requires reading the DVD image a second time (the first was from the network).
The efficient way to do it is to interleave the download and SHA1 computation. Then, you’ll get the checksum for free, because the entire process parallelizes so well:
# slightly contrived, to demonstrate process substitution wget -O - https://example.com/dvd.iso \ | tee >(sha1sum > dvd.sha1) > dvd.iso
tee write not just to the expected output file,
but also to a pipe running
sha1sum and saving the final
checksum in a file named
Note, however, that this example relies on a feature of modern shells
called process substitution
>(command)’ syntax, above;
See Process Substitution in The Bash Reference Manual.),
so it works with
but not with
/bin/sh. So if you write code like this
in a shell script, be sure to start the script with ‘
Note also that if any of the process substitutions (or piped stdout)
might exit early without consuming all the data, the
is needed to allow
tee to continue to process the input
to any remaining outputs.
Since the above example writes to one file and one process,
a more conventional and portable use of
tee is even better:
wget -O - https://example.com/dvd.iso \ | tee dvd.iso | sha1sum > dvd.sha1
You can extend this example to make
tee write to two processes,
computing MD5 and SHA1 checksums in parallel. In this case,
process substitution is required:
wget -O - https://example.com/dvd.iso \ | tee >(sha1sum > dvd.sha1) \ >(md5sum > dvd.md5) \ > dvd.iso
This technique is also useful when you want to make a compressed
copy of the contents of a pipe.
Consider a tool to graphically summarize disk usage data from ‘
For a large hierarchy, ‘
du -ak’ can run for a long time,
and can easily produce terabytes of data, so you won’t want to
rerun the command unnecessarily. Nor will you want to save
the uncompressed output.
Doing it the inefficient way, you can’t even start the GUI
until after you’ve compressed all of the
du -ak | gzip -9 > /tmp/du.gz gzip -d /tmp/du.gz | xdiskusage -a
tee and process substitution, you start the GUI
right away and eliminate the decompression completely:
du -ak | tee >(gzip -9 > /tmp/du.gz) | xdiskusage -a
Finally, if you regularly create more than one type of
compressed tarball at once, for example when
make dist creates
there may be a better way.
Makefile rules create
the two compressed tar archives with commands in sequence, like this
tardir=your-pkg-M.N tar chof - "$tardir" | gzip -9 -c > your-pkg-M.N.tar.gz tar chof - "$tardir" | bzip2 -9 -c > your-pkg-M.N.tar.bz2
However, if the hierarchy you are archiving and compressing is larger than a couple megabytes, and especially if you are using a multi-processor system with plenty of memory, then you can do much better by reading the directory contents only once and running the compression programs in parallel:
tardir=your-pkg-M.N tar chof - "$tardir" \ | tee >(gzip -9 -c > your-pkg-M.N.tar.gz) \ | bzip2 -9 -c > your-pkg-M.N.tar.bz2
If you want to further process the output from process substitutions, and those processes write atomically (i.e., write less than the system’s PIPE_BUF size at a time), that’s possible with a construct like:
tardir=your-pkg-M.N tar chof - "$tardir" \ | tee >(md5sum --tag) > >(sha256sum --tag) \ | sort | gpg --clearsign > your-pkg-M.N.tar.sig
An exit status of zero indicates success, and a nonzero value indicates failure.