Gnu/coreutils/cp-invocation

From Get docs

11.1 cp: Copy files and directories

cp copies files (or, optionally, directories). The copy is completely independent of the original. You can either copy one file to another, or copy arbitrarily many files to a destination directory. Synopses:

cp [option]… [-T] source dest
cp [option]… source… directory
cp [option]… -t directory source…
  • If two file names are given, cp copies the first file to the second.
  • If the --target-directory (-t) option is given, or failing that if the last file is a directory and the --no-target-directory (-T) option is not given, cp copies each source file to the specified directory, using the sources’ names.

Generally, files are written just as they are read. For exceptions, see the --sparse option below.

By default, cp does not copy directories. However, the -R, -a, and -r options cause cp to copy recursively by descending into source directories and copying files to corresponding destination directories.

When copying from a symbolic link, cp normally follows the link only when not copying recursively or when --link (-l) is used. This default can be overridden with the --archive (-a), -d, --dereference (-L), --no-dereference (-P), and -H options. If more than one of these options is specified, the last one silently overrides the others.

When copying to a symbolic link, cp follows the link only when it refers to an existing regular file. However, when copying to a dangling symbolic link, cp refuses by default, and fails with a diagnostic, since the operation is inherently dangerous. This behavior is contrary to historical practice and to POSIX. Set POSIXLY_CORRECT to make cp attempt to create the target of a dangling destination symlink, in spite of the possible risk. Also, when an option like --backup or --link acts to rename or remove the destination before copying, cp renames or removes the symbolic link rather than the file it points to.

By default, cp copies the contents of special files only when not copying recursively. This default can be overridden with the --copy-contents option.

cp generally refuses to copy a file onto itself, with the following exception: if --force --backup is specified with source and dest identical, and referring to a regular file, cp will make a backup file, either regular or numbered, as specified in the usual ways (see Backup options). This is useful when you simply want to make a backup of an existing file before changing it.

The program accepts the following options. Also see Common options.

-a
--archive

Preserve as much as possible of the structure and attributes of the original files in the copy (but do not attempt to preserve internal directory structure; i.e., ‘ls -U’ may list the entries in a copied directory in a different order). Try to preserve SELinux security context and extended attributes (xattr), but ignore any failure to do that and print no corresponding diagnostic. Equivalent to -dR --preserve=all with the reduced diagnostics.

--attributes-only

Copy only the specified attributes of the source file to the destination. If the destination already exists, do not alter its contents. See the --preserve option for controlling which attributes to copy.

-b
--backup[=method]

See Backup options. Make a backup of each file that would otherwise be overwritten or removed. As a special case, cp makes a backup of source when the force and backup options are given and source and dest are the same name for an existing, regular file. One useful application of this combination of options is this tiny Bourne shell script:

#!/bin/sh
# Usage: backup FILE...
# Create a GNU-style backup of each listed FILE.
fail=0
for i; do
  cp --backup --force --preserve=all -- "$i" "$i" || fail=1
done
exit $fail
--copy-contents

If copying recursively, copy the contents of any special files (e.g., FIFOs and device files) as if they were regular files. This means trying to read the data in each source file and writing it to the destination. It is usually a mistake to use this option, as it normally has undesirable effects on special files like FIFOs and the ones typically found in the /dev directory. In most cases, cp -R --copy-contents will hang indefinitely trying to read from FIFOs and special files like /dev/console, and it will fill up your destination disk if you use it to copy /dev/zero. This option has no effect unless copying recursively, and it does not affect the copying of symbolic links.

-d

Copy symbolic links as symbolic links rather than copying the files that they point to, and preserve hard links between source files in the copies. Equivalent to --no-dereference --preserve=links.

-f
--force

When copying without this option and an existing destination file cannot be opened for writing, the copy fails. However, with --force, when a destination file cannot be opened, cp then tries to recreate the file by first removing it. Note --force alone will not remove dangling symlinks. When this option is combined with --link (-l) or --symbolic-link (-s), the destination link is replaced, and unless --backup (-b) is also given there is no brief moment when the destination does not exist. Also see the description of --remove-destination.

This option is independent of the --interactive or -i option: neither cancels the effect of the other.

This option is ignored when the --no-clobber or -n option is also used.

-H

If a command line argument specifies a symbolic link, then copy the file it points to rather than the symbolic link itself. However, copy (preserving its nature) any symbolic link that is encountered via recursive traversal.

-i
--interactive

When copying a file other than a directory, prompt whether to overwrite an existing destination file. The -i option overrides a previous -n option.

-l
--link

Make hard links instead of copies of non-directories.

-L
--dereference

Follow symbolic links when copying from them. With this option, cp cannot create a symbolic link. For example, a symlink (to regular file) in the source tree will be copied to a regular file in the destination tree.

-n
--no-clobber

Do not overwrite an existing file; silently do nothing instead. This option overrides a previous -i option. This option is mutually exclusive with -b or --backup option.

-P
--no-dereference

Copy symbolic links as symbolic links rather than copying the files that they point to. This option affects only symbolic links in the source; symbolic links in the destination are always followed if possible.

-p
--preserve[=attribute_list]

Preserve the specified attributes of the original files. If specified, the attribute_list must be a comma-separated list of one or more of the following strings:

mode

Preserve the file mode bits and access control lists.

ownership

Preserve the owner and group. On most modern systems, only users with appropriate privileges may change the owner of a file, and ordinary users may preserve the group ownership of a file only if they happen to be a member of the desired group.

timestamps

Preserve the times of last access and last modification, when possible. On older systems, it is not possible to preserve these attributes when the affected file is a symbolic link. However, many systems now provide the utimensat function, which makes it possible even for symbolic links.

links

Preserve in the destination files any links between corresponding source files. Note that with -L or -H, this option can convert symbolic links to hard links. For example,

$ mkdir c; : > a; ln -s a b; cp -aH a b c; ls -i1 c
74161745 a
74161745 b

Note the inputs: b is a symlink to regular file a, yet the files in destination directory, c/, are hard-linked. Since -a implies --no-dereference it would copy the symlink, but the later -H tells cp to dereference the command line arguments where it then sees two files with the same inode number. Then the --preserve=links option also implied by -a will preserve the perceived hard link.

Here is a similar example that exercises cp’s -L option:

$ mkdir b c; (cd b; : > a; ln -s a b); cp -aL b c; ls -i1 c/b
74163295 a
74163295 b
context

Preserve SELinux security context of the file, or fail with full diagnostics.

xattr

Preserve extended attributes of the file, or fail with full diagnostics. If cp is built without xattr support, ignore this option. If SELinux context, ACLs or Capabilities are implemented using xattrs, they are preserved implicitly by this option as well, i.e., even without specifying --preserve=mode or --preserve=context.

all

Preserve all file attributes. Equivalent to specifying all of the above, but with the difference that failure to preserve SELinux security context or extended attributes does not change cp’s exit status. In contrast to -a, all but ‘Operation not supported’ warnings are output.

Using --preserve with no attribute_list is equivalent to --preserve=mode,ownership,timestamps.

In the absence of this option, the permissions of existing destination files are unchanged. Each new file is created with the mode of the corresponding source file minus the set-user-ID, set-group-ID, and sticky bits as the create mode; the operating system then applies either the umask or a default ACL, possibly resulting in a more restrictive file mode. See File permissions.

--no-preserve=attribute_list

Do not preserve the specified attributes. The attribute_list has the same form as for --preserve.

--parents

Form the name of each destination file by appending to the target directory a slash and the specified name of the source file. The last argument given to cp must be the name of an existing directory. For example, the command:

cp --parents a/b/c existing_dir

copies the file a/b/c to existing_dir/a/b/c, creating any missing intermediate directories.

-R
-r
--recursive

Copy directories recursively. By default, do not follow symbolic links in the source unless used together with the --link (-l) option; see the --archive (-a), -d, --dereference (-L), --no-dereference (-P), and -H options. Special files are copied by creating a destination file of the same type as the source; see the --copy-contents option. It is not portable to use -r to copy symbolic links or special files. On some non-GNU systems, -r implies the equivalent of -L and --copy-contents for historical reasons. Also, it is not portable to use -R to copy symbolic links unless you also specify -P, as POSIX allows implementations that dereference symbolic links by default.

--reflink[=when]

Perform a lightweight, copy-on-write (COW) copy, if supported by the file system. Once it has succeeded, beware that the source and destination files share the same disk data blocks as long as they remain unmodified. Thus, if a disk I/O error affects data blocks of one of the files, the other suffers the same fate.

The when value can be one of the following:

always

The default behavior: if the copy-on-write operation is not supported then report the failure for each file and exit with a failure status.

auto

If the copy-on-write operation is not supported then fall back to the standard copy behavior.

never

Disable copy-on-write operation and use the standard copy behavior.

This option is overridden by the --link, --symbolic-link and --attributes-only options, thus allowing it to be used to configure the default data copying behavior for cp. For example, with the following alias, cp will use the minimum amount of space supported by the file system.

alias cp='cp --reflink=auto --sparse=always'
--remove-destination

Remove each existing destination file before attempting to open it (contrast with -f above).

--sparse=when

A sparse file contains holes—a sequence of zero bytes that does not occupy any physical disk blocks; the ‘read’ system call reads these as zeros. This can both save considerable disk space and increase speed, since many binary files contain lots of consecutive zero bytes. By default, cp detects holes in input source files via a crude heuristic and makes the corresponding output file sparse as well. Only regular files may be sparse.

The when value can be one of the following:

auto

The default behavior: if the input file is sparse, attempt to make the output file sparse, too. However, if an output file exists but refers to a non-regular file, then do not attempt to make it sparse.

always

For each sufficiently long sequence of zero bytes in the input file, attempt to create a corresponding hole in the output file, even if the input file does not appear to be sparse. This is useful when the input file resides on a file system that does not support sparse files (for example, ‘efs’ file systems in SGI IRIX 5.3 and earlier), but the output file is on a type of file system that does support them. Holes may be created only in regular files, so if the destination file is of some other type, cp does not even try to make it sparse.

never

Never make the output file sparse. This is useful in creating a file for use with the mkswap command, since such a file must not have any holes.

--strip-trailing-slashes

Remove any trailing slashes from each source argument. See Trailing slashes.

-s
--symbolic-link

Make symbolic links instead of copies of non-directories. All source file names must be absolute (starting with ‘/’) unless the destination files are in the current directory. This option merely results in an error message on systems that do not support symbolic links.

-S suffix
--suffix=suffix

Append suffix to each backup file made with -b. See Backup options.

-t directory
--target-directory=directory

Specify the destination directory. See Target directory.

-T
--no-target-directory

Do not treat the last operand specially when it is a directory or a symbolic link to a directory. See Target directory.

-u
--update

Do not copy a non-directory that has an existing destination with the same or newer modification timestamp. If timestamps are being preserved, the comparison is to the source timestamp truncated to the resolutions of the destination file system and of the system calls used to update timestamps; this avoids duplicate work if several ‘cp -pu’ commands are executed with the same source and destination. This option is ignored if the -n or --no-clobber option is also specified. Also, if --preserve=links is also specified (like with ‘cp -au’ for example), that will take precedence; consequently, depending on the order that files are processed from the source, newer files in the destination may be replaced, to mirror hard links in the source.

-v
--verbose

Print the name of each file before copying it.

-x
--one-file-system

Skip subdirectories that are on different file systems from the one that the copy started on. However, mount point directories are copied.

-Z
--context[=context]

Without a specified context, adjust the SELinux security context according to the system default type for destination files, similarly to the restorecon command. The long form of this option with a specific context specified, will set the context for newly created files only. With a specified context, if both SELinux and SMACK are disabled, a warning is issued. This option is mutually exclusive with the --preserve=context option, and overrides the --preserve=all and -a options.

An exit status of zero indicates success, and a nonzero value indicates failure.