Gawk/Boolean-Ops

6.3.3 Boolean Expressions

A Boolean expression is a combination of comparison expressions or matching expressions, using the Boolean operators “or” (‘||’), “and” (‘&&’), and “not” (‘!’), along with parentheses to control nesting. The truth value of the Boolean expression is computed by combining the truth values of the component expressions. Boolean expressions are also referred to as logical expressions. The terms are equivalent.

Boolean expressions can be used wherever comparison and matching expressions can be used. They can be used in if, while, do, and for statements (see section Control Statements in Actions). They have numeric values (one if true, zero if false) that come into play if the result of the Boolean expression is stored in a variable or used in arithmetic.

In addition, every Boolean expression is also a valid pattern, so you can use one as a pattern to control the execution of rules. The Boolean operators are:

boolean1 && boolean2

True if both boolean1 and boolean2 are true. For example, the following statement prints the current input record if it contains both ‘edu’ and ‘li’:

if ($0 ~ /edu/ && $0 ~ /li/) print

The subexpression boolean2 is evaluated only if boolean1 is true. This can make a difference when boolean2 contains expressions that have side effects. In the case of ‘$0 ~ /foo/ && ($2 == bar++)’, the variable bar is not incremented if there is no substring ‘foo’ in the record.

boolean1 || boolean2

True if at least one of boolean1 or boolean2 is true. For example, the following statement prints all records in the input that contain either ‘edu’ or ‘li’:

if ($0 ~ /edu/ || $0 ~ /li/) print

The subexpression boolean2 is evaluated only if boolean1 is false. This can make a difference when boolean2 contains expressions that have side effects. (Thus, this test never really distinguishes records that contain both ‘edu’ and ‘li’—as soon as ‘edu’ is matched, the full test succeeds.)

! boolean

True if boolean is false. For example, the following program prints ‘no home!’ in the unusual event that the HOME environment variable is not defined:

BEGIN { if (! ("HOME" in ENVIRON))
            print "no home!" }

(The in operator is described in Referring to an Array Element.)

The ‘&&’ and ‘||’ operators are called short-circuit operators because of the way they work. Evaluation of the full expression is “short-circuited” if the result can be determined partway through its evaluation.

Statements that end with ‘&&’ or ‘||’ can be continued simply by putting a newline after them. But you cannot put a newline in front of either of these operators without using backslash continuation (see section awk Statements Versus Lines).

The actual value of an expression using the ‘!’ operator is either one or zero, depending upon the truth value of the expression it is applied to. The ‘!’ operator is often useful for changing the sense of a flag variable from false to true and back again. For example, the following program is one way to print lines in between special bracketing lines:

$1 == "START"   { interested = ! interested; next }
interested      { print }
$1 == "END"     { interested = ! interested; next }

The variable interested, as with all awk variables, starts out initialized to zero, which is also false. When a line is seen whose first field is ‘START’, the value of interested is toggled to true, using ‘!’. The next rule prints lines as long as interested is true. When a line is seen whose first field is ‘END’, interested is toggled back to false.³⁷

Most commonly, the ‘!’ operator is used in the conditions of if and while statements, where it often makes more sense to phrase the logic in the negative:

if (! some condition || some other condition) {
    … do whatever processing …
}

NOTE: The next statement is discussed in
The next Statement. next tells awk to skip the rest of the rules, get the next record, and start processing the rules over again at the top. The reason it’s there is to avoid printing the bracketing ‘START’ and ‘END’ lines.

Footnotes

(37)

This program has a bug; it prints lines starting with ‘END’. How would you fix it?